Looking for type of locktite to seal injection nozzles. I've done a search but could not find it.
Thanks
I used Loctite 609 with 7471 primer. Clean well and be quick though.
Safety wire them in. You dont need to glue them. Once glued, twice screwed.
For the injection nozzles going into the carb, I remember reading online to use a small amount of rubber contact cement.
I used Yamabond on one of mine that was loose.
See Tech Bulletin #M4-009
THE TECH LIBRARY »Yamaha Factory Specs and Info »Yamaha Technical Bulletins (http://www.2strokeworld.net/forum/index.php?topic=51.msg158#msg158)
Quote from: SoCal250 on April 11, 2020, 12:43:03 PM
See Tech Bulletin #M4-009
THE TECH LIBRARY »Yamaha Factory Specs and Info »Yamaha Technical Bulletins (http://www.2strokeworld.net/forum/index.php?topic=51.msg158#msg158)
So my memory is actually still working a bit. Good to know
Loctite green sleeve retainer #640
Chuck
https://www.emisupply.com/catalog/loctite-37424-sleeve-retainer-high-strength-tube-p-14298.html?utm_source=googprod&utm_medium=product_search&utm_campaign=google-product-search-us-en&utm_term=LOC-37424&gclid=Cj0KCQjwm9D0BRCMARIsAIfvfIY7laUqpZj6yCfVrnmmszTlkEMWa7xbr76m3nymfy94qV2Gi5qgOoUaAjkaEALw_wcB#.XpU31VVKjp8 (https://www.emisupply.com/catalog/loctite-37424-sleeve-retainer-high-strength-tube-p-14298.html?utm_source=googprod&utm_medium=product_search&utm_campaign=google-product-search-us-en&utm_term=LOC-37424&gclid=Cj0KCQjwm9D0BRCMARIsAIfvfIY7laUqpZj6yCfVrnmmszTlkEMWa7xbr76m3nymfy94qV2Gi5qgOoUaAjkaEALw_wcB#.XpU31VVKjp8)
Thanks for all the suggestions. Im going with the the #640,it looks like the right application.
Thanks
I've been doing that for 25 years that way...never had one fall out afterwards. And still on my huge 50ml bottle.
Here's the spec sheet and the reason so expensive, $55 a big bottle.
Chuck
http://media.hiscoinc.com/Volume2/d110001/medias/docus/205/Loctite%20Corporation-30769_135520-TDS_VD.pdf (http://media.hiscoinc.com/Volume2/d110001/medias/docus/205/Loctite%20Corporation-30769_135520-TDS_VD.pdf)
Quote from: SUPERTUNE on April 14, 2020, 10:38:33 AM
I've been doing that for 25 years that way...never had one fall out afterwards. And still on my huge 50ml bottle.
Here's the spec sheet and the reason so expensive, $55 a big bottle.
Chuck
http://media.hiscoinc.com/Volume2/d110001/medias/docus/205/Loctite%20Corporation-30769_135520-TDS_VD.pdf (http://media.hiscoinc.com/Volume2/d110001/medias/docus/205/Loctite%20Corporation-30769_135520-TDS_VD.pdf)
Thanks for your help
Since carb tuning is still going on after the update porting by Chuck, I'm just doing the zip ties. So far, so good: