Topics

https://www.ebay.com/itm/195754183269

-Chassis-
Sandblasted & powdercoated frame and swingarm satin black.
Re- packed steering head bearings.
New delrin swingarm bushings.
Polished upper triple clamp & risers.
Magura bars.
Replaced fork bushings, oil seals, & dust seals. 10wt fork oil.
Polished fork tubes.
Lightened and polished rear-set plates.

-Brakes-
Re-built front caliper.(OEM)
Re-built front master cyl.(OEM)
Made stainless-steel front brake hose.(EARL'S)
New front brake pads(EBC)
New rear brake shoes(EBC)
Dot 4 Motul fluid

-Engine/Trans-
New pistons. (Wiseco Yamaha Banshee)
Cylinders bored & honed.
New conn rods.(OE)
New conn rod bottom pins.(OE)
New upper & lower rod bearings & thrust bearings(OE)
New main bearings(OE)
Crank assembled by Semour
New transmission bearings(OE)
All new engine seals and gaskets(OE)
Replaced carb. gaskets & seals.
Replaced reed petals(Boyesson)

-Misc.-
New clutch cable.
Re-packed exhaust silencers, polished tips.
New AGM battery.
New Uni air filters.
New chain.

$4500

Located in Arizona.

Been gone a while. What is the current market pricing for RD350/400 bikes in the non-OEM/modified category these days?

Thanks

Interested in this one: https://www.batterytender.com/Battery-Tender-5.0AH-300CA-Lithium-Engine-Start-Battery-w-Smart-BMS

The built in protection circuit looks desirable to prevent over-charging.

Thanks

Top Fuel Motorcycle world record run at 5.50 / 264 mph by the legendary Nitro motorcycle drag racer Larry "Spiderman" McBride.

https://youtu.be/-xfb0XHJdTc

https://www.ebay.com/itm/282584662669?ul_noapp=true

Anyone use this Clutch Basket?

Found this link today: http://rrracing.co.nz

A few interesting pages.

https://www.treatland.tv/new-puch-peugeot-motobecane-vespa-moped-parts-s/88.htm


Treatland's Big BLACK FRIDAY 2019

tldr: 20% off use code "itsgumbotime" sale ends 12/2/2019

Black Friday is here!! Time to grab some treats at bargain basement prices. Oh and we have tons of NOS and used parts going into the store everyday, so this is the perfect time to grab some weird rare stuff that'll probably never show up here again!

Use sale code "itsgumbotime" to get 20% off your order total!

As always, free shipping applies to all orders over $150 within the continental united states. Once your cart is over $150 the option for free shipping will magically appear in the shipping carrier drop down menu.

Sale starts now and ends 12/2/2019 at 11:59pm PT! Better to order sooner than later as we will be taking off the 28th - 31st for the holidays.

A forum member on one of the other forums I belong to started a thread like this. Pretty much anything goes within reason. The thread is now several years & many thousands of posts long!

Here is a picture I took today.

Watching this movie again today.

Good Ole classic bike movie.

Perhaps On Any Sunday later on. 

https://youtu.be/EMrxee_fazo   

Might want to turn the sound track off.

Anyone ever heard of after-market fork springs & shocks for an MB5? 

I know... Tiny bike, only imported for 1 year, etc....

It's my most reliable, low mile, bike & it is kind of fun. Fork seal is beginning to leak & time to look into the possibilities. I would like to firm up the front end. Feels like the same spring strength as a toilet paper dispenser. 

Thanks.

Any benefit to fitting a velocity stack(s) about midway inside a UNI type of filter?