Topics

I haven't been able to locate a link.     It showed the step by step procedures with pictures and text to put an rd350 motor back together.

I used it once before to help me with my rd400 motor. Pictures were way better then the manual.  I believe it was a guy out of the UK.  It wasn't a video. 

Thanks

Well, I filled the bike with coolant.  Had two leaks.  I fixed one by tightening the a hose clamp. You can see where the other leak is coming from. 

Could you veterans give me any advice on how to fix the leak?  I hoping I don't have to pull the head since I just put it on.

This is a o-ringed head and I used permatex Motoseal gasket maker-grey.

I hope the pic works

Thanks

Any recommendations on a good Hi temp RTV silicone instant gasket?

I will be using it in place of the stock head gasket for my rz350.

Thanks

Installing a vape system.  The instructions say to bring one piston to TDC, then to adjust the rotor per instructions and tighten.

I read and seen a video in which the piston was brought up 1.8 BTDC.  Can anyone advice me on which it is?

Also, not sure the best way to torque the rotor.  No torque spec were given in the instructions.  I was just going to use a impact driver to torque the bolt down.???

Thanks in advance.

I have a new dial indicator from Economy Cycle. 

Can anyone tell me how to put an extension on.  It looks like I just need to unscrew the bottom cap and screw back on the extension.  If that is the case, then that cap is on real good.  Any suggestions on how to do this without damaging the dial gauge?

Thanks

Not mine but somewhat interested. 

https://honolulu.craigslist.org/oah/mcy/d/waianae-1995-aprilia-rs-250-reggiani/7610497052.html

Anyone have any knowledge on these bikes?  Are parts hard to come by?  I bet it is a lot of fun to ride.

I have been thinking about buying that RD 400 with the TZ350 engine (the blue one for 6,995.00).  Now this has come up.

Any thoughts on which would be a better bike to own?

Thanks

I ordered the red label yamalube from amazon.  I was sent the blue label yamalube.

Does anyone know if they are the same, just a new label?  I want to be sure.

Thanks

Well I got my rebuilt rz350 engine back.   

The problem is that the spring and washer under the push lever were missing.  I have a new washer and spring to install, however, can't seem to pull out the push lever.  I am known to break things.

Any advice would be greatly appreciated.

Oh, the tach drive gear wasn't installed either.  I have it, but it doesn't seem to want to go in.  Any advice on the tach gear would also be greatly appreciated.

Thank you to all.

Not mine.

https://orangecounty.craigslist.org/mcy/d/huntington-beach-yamaha-rz-350-two/7509349752.html

Not mine.

https://honolulu.craigslist.org/oah/mcy/d/honolulu-1988-dt-50/7489778102.html

Any idea how much it's really worth?  It looks like a fun bike!

I am breaking down a Daytona engine that sat for two plus decades.   Apparently moisture got into the cylinders.  The top of the pistons are visibly rusted.  it looks like the rust is just at the top where the rings are located.

Any ideas on how to free the pistons?

Thanks

Not mine.

It is all about timing.  I have been to Havasu four times this past year.  Going to be near there again in July.   Never the right time.

Doesn't look to bad at all.

I was hoping someone could recommend a good rotor puller for a daytona.

I tried the uppermost engine mounting bolt with an impact with no success.  I am afraid I my mess something up if I keep trying with the engine mounting bolt.

Any suggestions?

Thanks

Not mine.

https://losangeles.craigslist.org/sgv/mcy/d/duarte-1981-yamaha-rd350lc-all-original/7428268268.html

Anyone know what vendors might sale brake caliper adapters for R1 blue spot calipers. 

It is for a 1985 rz with stock rotors.  I was told that TDR racing had them.  I checked their website with no luck.

Thanks,
Russ

https://honolulu.craigslist.org/oah/mcy/d/kailua-1977-yamaha-rd400-for-sale/7310591063.html

Not mine.  It is pretty rare to see an RD for sell on Oahu. 

I wish there were more pictures.  Should of removed the one mirror before taking pics.

Hey HawaiiMike, Diablo007, do you know the owner?  (small island)

Not mine. 

Interesting.

https://losangeles.craigslist.org/wst/mcy/d/torrance-yamaha-rd350-with-lc-engine-in/7296636669.html

I am guessing some of you saw this already.

Not mine.

https://losangeles.craigslist.org/wst/mcy/d/santa-monica-1978-rd-400/7268294885.html

I wonder how many miles were on the old odometer?  Doesn't mention a bottom or top end rebuild. 

That is one way to reduce the miles on a motor (new speedo/odometer).

Not mine.

https://sfbay.craigslist.org/pen/mcy/d/millbrae-yamaha-rz-350/7262921361.html

I wonder how that bike would handle?  Do not care for the headlight.  Just doesn't look right to me.

I have a 1984 rz350.  Garrett has the engine so I am going to take some time and clean the rest up.

I was wondering if anyone knew the color of black (gloss, satin, low gloss) for black parts (kick stand, center stand, handle bars, horns, triple clamp, etc.)?  Even the rims are aluminum with black trim.  Not the red or gold trim that I have seen. 

I am also going to touch up the frame a little.  Based on my research that color is Fire Red. 

Lastly, I wanted to repaint the swing arm.  Can anyone suggest the silver color to use? 

Thanks