Turning Wrenches

help with solid state reg/rec

Started by Gil Gallad

Replies: 5
Views: 1,305

March 14, 2024, 01:40:39 PM
by Gil Gallad

Thicker Cylinder Gaskets for AC RD350

Started by Pravin

Replies: 2
Views: 1,102

March 13, 2024, 08:00:40 AM
by Pravin

Help! Installing HPI Ignition with No Battery

Started by svgarage

Replies: 6
Views: 1,954

March 08, 2024, 12:39:49 PM
by svgarage

RD400 Project Under Way

Started by Joe6v6

Replies: 2
Views: 1,020

March 07, 2024, 07:57:34 PM
by Joe6v6

RD400 Reed Petal Orientation

Started by Pravin

Replies: 3
Views: 1,293

March 02, 2024, 12:09:26 AM
by Pravin

Tabbed washer alternative

Started by STLMike

Replies: 12
Views: 3,206

February 24, 2024, 10:56:53 PM
by STLMike

RZ350 Transmission Dimension Specs Needed

Started by motodreams

Replies: 4
Views: 1,668

February 19, 2024, 10:52:43 PM
by motodreams

1977 RD400 using Uni Filter - Where the Air connection from Carburetor go

Started by KANDY

Replies: 2
Views: 1,342

February 18, 2024, 10:38:26 AM
by KANDY

90 degree inlet for LC motor from scratch

Started by m in sc

Replies: 4
Views: 1,250

February 13, 2024, 08:58:31 AM
by kpke

wrist pin press

Started by rdsarefun

Pages1 2

Replies: 19
Views: 3,903

February 12, 2024, 03:35:15 PM
by m in sc

the mystery debris in the motor. (kawi 120) wtf

Started by m in sc

Pages1 2 3

Replies: 40
Views: 6,408

February 09, 2024, 08:44:24 AM
by Striker1423

Suzuki TS 400

Started by Rgvnfla

Replies: 6
Views: 1,567

January 28, 2024, 04:15:03 AM
by busa1300

Help - RZ350 Headlight Install

Started by TeeZee

Replies: 4
Views: 1,947

January 22, 2024, 01:09:11 PM
by TeeZee

blown main fuse

Started by RDryan

Pages1 2

Replies: 28
Views: 5,720

January 14, 2024, 07:32:31 PM
by RDryan

RD350 wheels

Started by STLMike

Replies: 12
Views: 3,260

January 14, 2024, 01:26:42 PM
by teazer

reviving an old inner tube thread and question about rim strips

Started by rdsarefun

Replies: 3
Views: 1,218

January 12, 2024, 03:51:35 PM
by 85RZwade

RD400F frame info

Started by car91r

Replies: 0
Views: 886

January 10, 2024, 09:03:14 AM
by car91r

Designing a pipe. Am I doing this right?

Started by FinnishFish

Replies: 9
Views: 3,548

January 09, 2024, 02:30:20 PM
by m in sc

Timing with a dial gauge

Started by rearwheelslider

Pages1 2

Replies: 16
Views: 5,483

January 08, 2024, 01:33:54 PM
by m in sc

Base gasket

Started by dgorms

Replies: 8
Views: 2,457

January 05, 2024, 04:01:00 PM
by rearwheelslider